ARUBA access points allow you to deploy and manage high-speed networks while also providing best-in-class security, reliable network performance, and flexible scalability. Browse Aruba solutions or contact a servermonkey expert and start your journey to a growing high-performance, secure network solution that can grow with you.

As a trusted Aruba reseller, ServerMonkey offers the Aruba Indoor 510 AP Series at competitive rates, providing businesses with access to top-tier networking hardware.

Request a Quote

Details:

Description

Hardware variants
AP-514: External antenna models AP-515: Internal antenna models
Wi-Fi radio specifications
AP type: Indoor, dual radio, 5GHz 802.11ax 4x4 MIMO and 2.4 GHz 802.11ax 2x2 MIMO 5GHz radio: Four spatial stream Single User (SU) MIMO for up to 4.8Gbps wireless data rate to individual 4SS HE160 802.11ax client devices (max) Two spatial stream Single User (SU) MIMO for up to 1.2Gbps wireless data rate to individual 2SS HE80 802.11ax client devices (typical) Four spatial stream Multi User (MU) MIMO for up to 4.8Gbps wireless data rate to up to four 1SS or two 2SS HE160 802.11ax DL-MU-MIMO capable client devices simultaneously (max) Four spatial stream Multi User (MU) MIMO for up to 2.4Gbps wireless data rate to up to four 1SS or two 2SS HE80 802.11ax DL-MU-MIMO capable client devices simultaneously (typical) 2.4GHz radio: Two spatial stream Single User (SU) MIMO for up to 574Mbps wireless data rate to 2SS HE40 802.11ax client devices (max) Two spatial stream Single User (SU) MIMO for up to 287Mbps wireless data rate to 2SS HE20 802.11ax client devices (typical) Support for up to 512 associated client devices per radio, and up to 16 BSSIDs per radio Supported frequency bands (country-specific restrictions apply): 2.400 to 2.4835GHz ISM 5.150 to 5.250GHz U-NII-1 5.250 to 5.350GHz U-NII-2A 5.470 to 5.725GHz U-NII-2C 5.725 to 5.850GHz U-NII-3/ISM 5.850 to 5.895GHz U-NII-4 Available channels: Dependent on configured regulatory domain Dynamic Frequency Selection (DFS) optimizes the use of available RF spectrum Including Zero-Wait DFS (ZWDFS) to accelerate channel changes Supported radio technologies: 802.11b: Direct-Sequence Spread-Spectrum (DSSS) 802.11a/g/n/ac: Orthogonal frequency-division multiplexing (OFDM) 802.11ax: Orthogonal frequency-division multiple access (OFDMA) with up to 16 resource units (for an 80MHz channel) Supported modulation types: 802.11b: BPSK, QPSK, CCK 802.11a/g/n: BPSK, QPSK, 16-QAM, 64-QAM, 256-QAM (proprietary extension) 802.11ac: BPSK, QPSK, 16-QAM, 64-QAM, 256‑QAM, 1024-QAM (proprietary extension) 802.11ax: BPSK, QPSK, 16-QAM, 64-QAM, 256-QAM, 1024-QAM 802.11n high-throughput (HT) support: HT20/40 802.11ac very high throughput (VHT) support: VHT20/40/80/160 802.11ax high efficiency (HE) support: HE20/40/80/160 Supported data rates (Mbps): 802.11b: 1, 2, 5.5, 11 802.11a/g: 6, 9, 12, 18, 24, 36, 48, 54 802.11n (2.4 GHz): 6.5 to 300 (MCS0 to MCS15, HT20 to HT40) 802.11n (5 GHz): 6.5 to 600 (MCS0 to MCS31, HT20 to HT40) 802.11ac: 6.5 to 3,467 (MCS0 to MCS9, NSS = 1 to 4, VHT20 to VHT160) 802.11ax (2.4 GHz): 3.6 to 574 (MCS0 to MCS11, NSS = 1 to 2, HE20 to HE40) 802.11ax (5GHz): 3.6 to 4,803 (MCS0 to MCS11, NSS = 1 to 4, HE20 to HE160) 802.11n/ac/ax packet aggregation: A-MPDU, A-MSDU Transmit power: Configurable in increments of 0.5 dBm Maximum (aggregate, conducted total) transmit power (limited by local regulatory requirements): 2.4 GHz band: +21 dBm (18dBm per chain) 5 GHz band: +24 dBm (18 dBm per chain) Note: conducted transmit power levels exclude antenna gain. For total (EIRP) transmit power, add antenna gain. Advanced Cellular Coexistence (ACC) minimizes the impact of interference from cellular networks Maximum Ratio Combining (MRC) for improved receiver performance Cyclic Delay/Shift Diversity (CDD/CSD) for improved downlink RF performance Space-Time Block Coding (STBC) for increased range and improved reception Low-Density Parity Check (LDPC) for high-efficiency error correction and increased throughput Transmit Beam-Forming (TxBF) for increased signal reliability and range 802.11ax Target Wait Time (TWT) to support low‑power client devices 802.11mc Fine Timing Measurement (FTM) for precision distance ranging
Wi-Fi antennas
AP-514: Four (female) RP-SMA connectors for external dual band antennas (A0 through A3, corresponding with radio chains 0 through 3 for 5GHz; 2.4GH radio uses A0/A1 and chains 0/1 only). Worst-case internal loss between radio interface and external antenna connectors (due to diplexing circuitry): 1.3dB in 2.4GHz and 1.7dB in 5GHz. AP-515: Four integrated dual-band downtilt omni-directional antennas for 4x4 MIMO (2x2 MIMO for 2.4GHz) with peak antenna gain of 4.2dBi in 2.4GHz and 7.5dBi in 5GHz. Built-in antennas are optimized for horizontal ceiling mounted orientation of the AP. The downtilt angle for maximum gain is roughly 30 degrees. Combining the patterns of each of the antennas of the MIMO radios, the peak gain of the effective per-antenna pattern is 3.8dBi in 2.4 GHz and 4.6dBi in 5 GHz.
Additional interfaces
E0: HPE SmartRate port (RJ-45, maximum negotiated speed 2.5 Gbps) Auto-sensing link speed (100/1000/2500BASE-T) and MDI/MDX 2.5Gbps speeds comply with NBase-T and 802.3bz specifications PoE-PD: 48Vdc (nominal) 802.3af/at/bt (class 3 or higher) 802.3az Energy Efficient Ethernet (EEE) E1: 10/100/1000BASE-T Ethernet network interface (RJ-45) Auto-sensing link speed and MDI/MDX 802.3az Energy Efficient Ethernet (EEE) Link Aggregation (LACP) support between both network ports for redundancy and increased capacity DC power interface: 12Vdc (nominal, +/-5%), accepts 2.1mm/5.5mm center-positive circular plug with 9.5mm length USB 2.0 host interface (Type A connector) Capable of sourcing up to 1A/5W to an attached device Bluetooth 5 and Zigbee (802.15.4) radio (2.4GHz) Bluetooth 5: up to 8dBm transmit power (class 1) and -95dBm receive sensitivity Zigbee: up to 8dBm transmit power and -97dBm receive sensitivity Integrated vertically polarized omnidirectional antenna with roughly 30 degrees downtilt and peak gain of 3.5dBi (AP-515) or 4.9dBi (AP-514) Visual indictors (two multi-color LEDs): for System and Radio status Reset button: factory reset, LED mode control (normal/off) Serial console interface (proprietary, micro-B USB physical jack) Kensington security slot
Power sources and power consumption
The AP supports direct DC power and Power over Ethernet (PoE; on port E0) When both power sources are available, DC power takes priority over PoE Power sources are sold separately; see the ordering Information section below for details When powered by DC or 802.3at (class 4)/802.3bt (class 5) PoE, the AP will operate without restrictions. When powered by 802.3af (class 3) PoE and with the IPM feature enabled, the AP will start up in unrestricted mode, but it may apply restrictions depending on the PoE budget and actual power. What IPM restrictions to apply, and in what order, is programmable. Operating the AP with an 802.3af (class 3 or lower) PoE source and IPM disabled is not supported (except for AP staging; no radios will be enabled). Maximum (worst-case) power consumption: DC powered: 16.0W PoE powered (802.3af, IPM enabled): 13.5W PoE powered (802.3at/bt): 20.8W All numbers above are without an external USB device connected. When sourcing the full 5W power budget to such a device, the incremental (worst‑case) power consumption for the AP is up to 5.7W (PoE powered) or 5.5W (DC powered). Maximum (worst-case) power consumption in idle mode: 12.6W (POE) or 9.7W (DC) Maximum (worst-case) power consumption in deep‑sleep mode: 5.9W (POE) or 1.5W (DC)
Mounting details
A mounting bracket has been pre-installed on the back of the AP. This bracket is used to secure the AP to any of the (sold separately) mount kits; see the ordering Information section below for details.
Mechanical
Dimensions/weight (AP-515; unit, excluding mount bracket): 200mm (W) x 200mm (D) x 46mm (H)/7.9" (W) x 7.9" (D) x 1.8" (H) Weight: 810g(28.5oz) Dimensions/weight (AP-515; shipping): 230mm (W) x 220mm (D) x 72mm (H)/9.1" (W) x 8.7" (D) x 2.8" (H) Weight: 1010g(35.5oz)
Environmental
Operating conditions Temperature: 0C to +50C/+32F to +122F Humidity: 5% to 93% non-condensing AP is plenum rated for use in air-handling spaces ETS 300 019 class 3.2 environments Storage and transportation conditions Temperature: -40C to +70C/-40F to +158F Humidity: 5% to 93% non-condensing ETS 300 019 classes 1.2 and 2.3 environments
Reliability
Mean Time Between Failure (MTBF): 560,000hrs (64yrs) at +25C operating temperature.
Regulatory compliance
FCC/ISED CE Marked RED Directive 2014/53/EU EMC Directive 2014/30/EU Low Voltage Directive 2014/35/EU UL/IEC/EN 60950 EN 60601-1-1, EN60601-1-2 Railway Certs (AP-515 Only): EN 50155:2017 – Railway Applications EN 50121-1:2017—Railway EMC EN 50121-3-2—Railway EMC EN 50121-4:2016—Railway Immunity IEC 61373 ed2:2008—Railway Shock and Vibration For more country-specific regulatory information and approvals, please see your HPE Aruba Networking representative.
Regulatory model numbers
AP-514: APIN0514 AP-515: APIN0515
Certifications
UL2043 plenum rating Wi-Fi Alliance: Wi-Fi CERTIFIED a, b, g, n, ac, ax WPA, WPA2 and WPA3—Enterprise with CNSA option, Personal (SAE), Enhanced Open (OWE) WMM, WMM-PS, W-Fi Agile Multiband Passpoint (release 2) Wi-Fi CERTIFIED Location™ Bluetooth SIG
Minimum operating system software versions
HPE Aruba Networking Operating System and HPE Aruba Networking InstantOS 8.4.0.0 (with some restrictions). For unrestricted operation, use 8.6.0.0 or later. HPE Aruba Networking Operating System 10.0.0.0
Warranty
HPE Aruba Networking's hardware limited lifetime warranty.

CONTACT US TO LEARN MORE

ABOUT Aruba Indoor 510 AP Series

Fill out the form and our team will get back to you.

1-855-432-8918
[email protected]
2130 W Sam Houston Pkwy N
Houston, TX 77043

Aruba Indoor 510 AP Series

CONTACT US TO LEARN MORE

ABOUT Aruba Indoor 510 AP Series

What are you looking for?

Get to Know Us

Resources

What We Do

Customer Service

Follow Us