Details:
Description
Hardware variants
  • AP-605H:
    • Hospitality AP platform, integrated antennas
Wi-Fi radio specifications
  • AP type: Indoor, tri‑band, 2.4GHz, 5GHz and 6GHz (dual concurrent) 802.11ax 2x2 MIMO
  • 2.4GHz radio: Two spatial stream Single User (SU) MIMO for up to 574Mbps wireless data rate with 2SS HE40 802.11ax client devices (287Mbps for HE20)
  • 5GHz radio: Two spatial stream Single User (SU) MIMO for up to 1.2Gbps wireless data rate with 2SS HE80 802.11ax client devices
  • 6GHz radio: Two spatial stream Single User (SU) MIMO for up to 2.4Gbps wireless data rate with 2SS HE160 802.11ax client devices
  • Up to 512 associated client devices per radio, and up to 16 BSSIDs per radio (limited to 8 for the 6GHz radio)
  • Supported frequency bands (country‑specific restrictions apply): 
    • 2.400 to 2.4835GHz >ISM 
    • 5.150 to 5.250GHz > U-NII-1 
    • 5.250 to 5.350GHz > U-NII-2A 
    • 5.470 to 5.725GHz > U-NII-2C 
    • 5.725 to 5.850GHz > U‑NII‑3/ISM 
    • 5.850 to 5.895GHz > U-NII-4 
    • 5.925 to 6.425GHz > U-NII-5 
    • 6.425 to 6.525GHz > U-NII-6 
    • 6.525 to 6.875GHz > U-NII-7 
    • 6.875 to 7.125GHz > U-NII-8
  • Available bands and channels: Dependent on configured regulatory domain (country)
  • Dynamic frequency selection (DFS) optimizes the use of available RF spectrum in the 5GHz band
  • Supported radio technologies:
    • 802.11b: Direct-sequence spread-spectrum (DSSS) 
    • 802.11a/g/n/ac: Orthogonal frequency-division multiplexing (OFDM) 
    • 802.11ax: Orthogonal frequency-division multiple access (OFDMA) with up to 8 resource units
  • Supported modulation types:
    • 802.11b: BPSK, QPSK, CCK -802.11a/g/n: BPSK, QPSK, 16‑QAM, 64‑QAM and 256‑QAM (proprietary extension) 
    • 802.11ac: BPSK, QPSK, 16‑QAM, 64‑QAM, 256‑QAM and 1024‑QAM (proprietary extension)
    • 802.11ax: BPSK, QPSK, 16‑QAM, 64‑QAM, 256‑QAM and 1024‑QAM
  • 802.11n high-throughput (HT) support:
    • HT20/40
  • 802.11ac very high throughput (VHT) support:
    • VHT20/40/80
  • 802.11ax high efficiency (HE) support:
    • HE20/40/80/160
  • Supported data rates (Mbps):
    • 802.11b: 1, 2, 5.5, 11 
    • 802.11a/g: 6, 9, 12, 18, 24, 36, 48, 54 
    • 802.11n: 6.5 to 300 (MCS0 to MCS15, HT20 to HT40), 400 with 256‑QAM (proprietary extension) 
    • 802.11ac: 6.5 to 867 (MCS0 to MCS9, NSS = 1 to 2, VHT20 to VHT80); 1,083 with 1024‑QAM (MCS10 and MCS11, proprietary extension) 
    • 802.11ax (2.4GHz): 3.6 to 574 (MCS0 to MCS11, NSS = 1 to 2, HE20 to HE40) 
    • 802.11ax (5GHz): 3.6 to 1,201 (MCS0 to MCS11, NSS = 1 to 2, HE20 to HE80) 
    • 802.11ax (6GHz): 3.6 to 2,402 (MCS0 to MCS11, NSS = 1 to 2, HE20 to HE160)
  • 802.11n/ac packet aggregation:
    • A-MPDU, A-MSDU
  • Transmit power:
    • Configurable in increments of 0.5 dBm
  • Maximum (aggregate, conducted total) transmit power (limited by local regulatory requirements): 
    • Per radio/band (2.4GHz / 5GHz / 6GHz): +21 dBm (18dBm per chain)
    • Note: conducted transmit power levels exclude antenna gain. For total (EIRP) transmit power, add antenna gain
  • Minimum configurable transmit power is –10dBm (conducted, per chain)
  • Advanced cellular coexistence (ACC) minimizes the impact of interference from cellular networks
  • Cyclic delay/shift diversity (CDD/CSD) for improved downlink RF performance
  • Space-time block coding (STBC) for increased range and improved reception
  • Low‑density parity check (LDPC) for high‑efficiency error correction and increased throughput
  • Transmit beamforming (TxBF) for increased signal reliability and range
  • 802.11ax target wait time (TWT) to support low-power client devices
  • 802.11mc fine timing measurement (FTM) for precision distance ranging
Wi-Fi antennas
  • AP-605H:
    • Integrated omni-directional antennas for 2x2 MIMO with peak antenna gain of 5.1dBi in 2.4GHz, 5.1dBi in 5GHz and 5.4dBi in 6GHz. The built-in antennas are optimized for vertical wall or desk mounted orientation of the AP.
      • Combining the patterns of each of the antennas of the MIMO radios, the peak gain of the combined, average pattern is 4.4dBi in 2.4GHz, 4.4dBi in 5GHz and 4.0dBi in 6 GHz
Other interfaces and features
  • Uplink (E0): Ethernet wired network port (RJ-45) 
    • Auto-sensing link speed (100/1000/2500BASE-T) and MDI/ MDX
    • 2.5Gbps speed complies with NBase-T and 802.3bz specifications  
    • 802.3az Energy Efficient Ethernet (EEE)
    • POE-PD: 48Vdc (nominal) 802.3af/at/bt POE (class 3, 4 or 6)
  • Downlink (E1-E4): Ethernet wired network ports (RJ-45) 
    • Auto-sensing link speed (10/100/1000BASE-T) and MDI/ MDX 
    • 802.3az Energy Efficient Ethernet (EEE) 
    • E1&E2: POE‑PSE: 802.3af/at POE output; dual 802.3af (both ports) or single 802.3at (E1 only); 30W max
  • DC power interface
    • Circular: 48Vdc (nominal, +/‑ 5%), accepts 1.35mm/3.5mm center‑positive circular plug with 9.5mm length
  • USB 2.0 host interface (Type A connector) 
    • Capable of sourcing up to 1A / 5W to an attached device
    • USB device can be physically secured with locking screw
  • Bluetooth Low Energy (BLE5.0) and Zigbee (802.15.4) radio
    • BLE: up to 3dBm transmit power (class 1) and ‑98dBm receive sensitivity (125kbps) 
    • Zigbee: up to 3dBm transmit power and ‑96dBm receive sensitivity (250kbps) 
    • Integrated omni-directional antenna with roughly 30 to 40 degrees down tilt and peak gain of 3.5dBi
  • GNSS L1 (1575.42MHz) receiver supporting GPS, Galileo, GLONASS and BeiDou signals 
    • Receive sensitivity: -162dBm (tracking) 
    • Integrated omni-directional antenna with roughly 30 to 40 degrees down tilt and peak gain of 4.5dBi
  • Advanced IOT coexistence (AIC) allows concurrent operation of multiple radios in the 2.4GHz band
  • Built-in trusted platform module (TPM 2.0) for enhanced security and anti-counterfeiting
  • Visual system status indicators (LEDs):
    • Power/system status
    • Radio status
    • Local network port status (4x)
    • POE-PSE status (2x)
  • Serial console interface (proprietary, micro‑B USB physical jack)
  • Reset button: factory reset, LED mode control (normal/off)
  • Kensington security slot
  • Automatic thermal shutdown and recovery function
Power sources and power consumption
  • The AP supports direct DC power and Power over Ethernet
  • When both DC and POE power sources are available, DC power takes priority over POE
  • Power sources are sold separately; see the 600H Series Ordering Guide for details
  • The AP-605HR bundles include an AC-to-DC power adapter
  • When powered by DC or 802.3bt (class 6) POE, the AP will operate without restrictions
  • When powered by 802.3at (class 4) POE and with the IPM feature disabled, the AP will disable the USB port (only) if POE-PSE is enabled, and support (802.3af) POE-PSE power on E1 only (no PSE on E2)
  • When powered by 802.3af (class 3) POE with the IPM feature disabled, the AP will disable the USB port and POE-PSE capability. With IPM enabled, the AP will start up without restrictions, but may dynamically apply additional restrictions depending on the POE budget and actual power consumption. The feature specific restrictions and order in which they are applied can be configured.
  • Maximum (worst-case) power consumption (AP only / USB adder / POE PSE adder):
    • DC powered: 14.9W / 5.8W / 27.5W
    • POE powered: 13.9W / 5.8W / 30.1W
  • Maximum (worst-case) power consumption in idle mode (AP only):
    • DC powered: 5.8W
    • POE powered: 5.9W
  • Maximum (worst-case) power consumption in deep-sleep mode (AP only):
    • DC powered: 1.5W
    • POE powered: 1.4W
Mounting details
  • Using one of the (separate orderable) mount kits, the AP can be attached to a single or dual gang wall-box,
    directly to a wall, or desk mounted. See the 600H Series Ordering Guide for details.
Mechanical specifications
  • Dimensions/weight (AP-605H; unit):
    • 105mm (W) x 40 mm (D) x 153 mm (H)
    • 500g
  • Dimensions/weight (AP-605H; shipping):
    • 145 mm (W) x 64 mm (D) x 210 mm (H)
    • 690 g
Environmental specifications
  • Operating conditions
    • Temperature: 0C to +40C / +32F to +104F
    • Relative humidity: 5% to 95%
    • ETS 300 019 class 3.2 environments
    • AP is plenum rated for use in air-handling spaces
  • Storage conditions
    • Temperature: -25C to +55C / +13F to +131F
    • Relative humidity: 10% to 100%
    • ETS 300 019 class 1.2 environments
  • Transportation conditions
    • Temperature: -40C to +70C / -40F to +158F
    • Relative humidity: up to 95%
    • ETS 300 019 class 2.3 environments
Reliability
  • Mean time between failure (MTBF): 999 khrs. (114 yrs.) at +25C ambient operating temperature.
Regulatory compliance
  • FCC/ISED
  • CE Marked
  • RED Directive 2014/53/EU
  • EMC Directive 2014/30/EU
  • Low Voltage Directive 2014/35/EU
  • IEC/EN 62368-1
  • EN 60601-1-1, EN60601-1-2
  • UL2043

For more country-specific regulatory information and approvals, please see your HPE Aruba Networking representative.

Regulatory model numbers
  • AP-605H access points (all models): APINH605
Certifications
  • Wi-Fi Alliance (WFA):
    • Wi-Fi CERTIFIED a, b, g, n, ac
    • Wi-Fi CERTIFIED 6
    • WPA, WPA2 and WPA3 – Enterprise with CNSA option, Personal (SAE), Enhanced Open (OWE)
    • WMM, WMM-PS, Wi-Fi Agile Multiband
    • Wi-Fi CERTIFIED Location TM
  • Bluetooth SIG
  • Ethernet Alliance (POE PD device, class 6 and POE PSE device, class 4)
Warranty
Minimum operating system software versions
  • HPE Aruba Networking Wireless Operating System 10.7.0.0 (AOS-10.7.0.0)
  • HPE Aruba Networking Wireless Operating System 8.12.0.0 (AOS-8.12.0.0)
  • HPE Aruba Networking Instant Operating System 8.12.0.0 (Instant-8.12.0.0)

CONTACT US TO LEARN MORE

ABOUT Aruba Remote and Hospitality AP 600H Series

Fill out the form and our team will get back to you.

What are you looking for?